Skip to main content

Filter By:

Parts & Accessories

$42.99
Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.
$54.99
Pedal Axle Rebuild Kit for SPIKE & OOZY Trail Pedals - 1 set L&R axle - 2pcs IGUS bushing - 2pcs O-ring - 2pcs dust cap - 2pcs stainless shim washer - 2pcs silicone friction seal - 2pcs lock nut
$11.99
IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer
$8.99
Shorter 7mm rear load pins for the outer extremities of SPOON, SPIKE, and OOZY pedals. - Provide durability and improved safety - Mix and match with the longer stock pins to customize your ideal amount of grip
$49.99
- Crank boots compatible axle rebuild kits for SPIKE and OOZY pedals (with bright green friction seals), produced in 2015 or later. Bearings must be purchased separately. - Crank boots compatible axle - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs
$11.99
Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included
$49.99
The Spoon Pedal Axle Rebuild kit includes the internal parts required to completely rebuild a set of Spoon pedals. - Pins available separately
$19.99
Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.
$12.99
Polyurethane pads with diamond plate traction pattern allow riders to customize their pedals for a perfect interface with any shoe. - Kit includes eight 1mm traction pads and eight 2mm traction pads
$37.99
Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals
$10.99
Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.
$68.99
Widen your Q-factor to 57mm. - Long spindles are 5mm longer than standard. - The kit includes: 1 pair long spindles + refresh kit (Enduro cartridge bearings, igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double shot, model years 2010-present - Weight: 112g per pair - Spindle material: forged SCM 435 chromoly steel - Q-factor: 57mm
$38.99
A revolution in performance and reliability. The kit includes premium internal components: - Enduro catridge bearings - Enduro sealed needle bearing - Double seal system (internal and external seals) - Hex alloy end caps - O-rings, nuts - Sleeve bushings - Bearing removal tool
$38.99
A revolution in performance and reliability. The kit includes premium internal components: - Inner bearing o-ring x 2 - Spindle seal x 2 - Outer Igus solid bearing x 2 - Inner Igus solid bearing half x 4 - Bearing Retainer Bolt x 4 - Outer o-ring x 2 - Grease port screw x 2 - Compatibility: Stamp (2016), Stamp 7 (2017+), Stamp 11 (2017+)
$37.99
Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees
$39.99
Crank Brothers' Quattro 3-hole cleats let you use Crank Bros. pedals with your road shoes. The cleat and walking plate mount directly to shoes that use a traditional 3-hole mounting setup. - Weight (pair): 86 grams - Shoe compatibility: LOOK/SPD-SL - Release angle: 15 or 20 degrees
$14.99
Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs
$239.99
The ultimate weight-saving upgrade.  - The kit includes: 1 pair titanium spindles + refresh kit (Enduro cartridge bearings, Igus ll-glide bearings, DSS double seal system: internal and external seals, hex alloy end caps, o-rings, nuts, sleeve bushings, & bearing removal tool). - Compatible with: Eggbeater, Candy, Mallet, 5050, Double Shot, model years 2010-present - Weight: 60g per pair - Spindle material: 6al/4v titanium - Max. rider weight: 200lb/90kg - Q-factor: 52 mm
$37.99
Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees
Page 1 of 1